KAJI EKSPERIMEN MODEL PATAHAN PADA AL 6061 – ABU DASAR BATU BARA YANG MENDAPAT PERLAKUAN PANAS
Abstract
Composite is a blend of two materials or that have a different phase becoming a new material, which has
better properties than both. If fusion is occurring microscopic (molecular level) then referred to as alloy / blend.
This study aims to analyze the surface of the fatigue test results using Macro photograph and SEM-EDX. In this
study was observed fracture fatigue test results. To determine the morphology of each treatment and no treatment.
Conclusions testing fatigue fracture surface photograph can find out which models are tired of the results of a
fatigue fracture. The method is used, using the test results broken fatigue rotary bending fatigue fracture by taking a
look at the best cycle. Then, after the material was broken in doing observations mikroskope photo to view the
microstructure and phase formed from each treatment and without heat treatment, after it is done using the STEMI
DV4 macro image to see the surface of the account after break tired. And to see perpatan composition using SEMEDX
Inspect S50 to see the line and the composition of the material that gets the heat treatment and without
sediment heat treatment.
Keywords: Composites, fatigue fracture fatigue, Structure mikroskope, Photo Macro, SEM-EDX
Downloads
References
http://Digilib.Unimed.Ac.Id/Public/UNIMEDNondegree-22887-Bab%20I.Pdf
https://Id.Scribd.Com/Doc/216733130/Pemilihan
Bahan
https://Zackcapitano.Wordpress.Com/2012/11/07/
Pengaruh
Normalizing Ulangterhadapsifat Baja Din
mnv7 (Muchtarkarokaro )Jurusanteknikmesin
Fti-Its Surabaya Just Another Wordpress.Com
Weblog
Mekanika Perpatahan Elly Arbintarso Linear Elastic
Fracture Mechanics (Lef) Hendri Chandra
Mechanical Enginering Department Faculty Of
Engineering University Of Sriwijaya 2009
Karakteristik Laju Perambatan Retak Fatik Dan
Retak Korosi Tegangan Sambungan Las Baha
Tahan Karat Aisi 304 Dan Baja Karbon Rendah
Ss 400 Yang Di-Flime Heating Dengan Air ( Hari
Prasetyo) Jurusan Teknik Mesin Fakultas Teknik
Universitas Sebelas Maret Surakarta (2007)
Karakterisasi Perilaku Perambatan Retak Fatik Dan
Korosi Retak Tegang Dalam Larutan Cacl2 40%
Dengan Inhibitor Sodium Silikat Dan Zeolit Pada
Sambungan Las Gtaw Baja Tahan Karat 304
Adhirohadhi, Rochman Rochiem, Hariyati
Purwaningsih Jurusan Teknik Material &
Metalurgi, Fakultas Teknologi Industri, Its,
Surabaya
Pengaruh Lama Sonikasi Pada Pembuatan Film
Pani-Ag/Ni Terhadap Kristalinitas Dan
Konduktivitasnya Faradilla Parasmayanti
Universitas Negeri Malang Fakultas Matematika
Dan Ilmu Pengetahuan Alam Program Studi
Fisika Mei 2014
Analisa Karakteristik Material Spoke Wheel Dengan
Cast Wheel Pada Pelek Sepeda Motor Sasi
Kirono, Adi Purnomo Universitas
Muhammadiyah Jakarta, Jurusan Teknik Mesin
Analisa Kegagalan Pada Poros Baja Karbon S45c
Aplikasi Komponen As Sink Roll Cahya Sutowo,
Budi Priyono Pusat Penelitian Metalurgi dan
Material –LIPI Kawasan Puspiptek Serpong,
Gedung 470, Tangerang 15314
Mekanika : Jurnal Teknik Mesin allows readers to read, download, copy, distribute, print, search, or link to the full texts of its articles and allow readers to use them for any other lawful purpose. The journal allows the author(s) to hold the copyright without restrictions. Finally, the journal allows the author(s) to retain publishing rights without restrictions